|
Crosshead Nut Wrench
935-351
For removing and installing individual cylinder heads. Attaches directly and quickly to the tapped holes in the cylinder head. No tools are required. The two lifting holes will position the head either level for the inline engines or at an angle for the vee engines.
Top
|
|
Rod Insertion Tool
939-978
This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on SW frames.
Top
|
|
|
Rod Insertion Tool
904-923
This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on W-6 frames.
Top
|
|
|
Rod Insertion Tool
904-925
This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on MW frames.
Top
|
|
|
Rod Insertion Tool
904-925-003
This tool is used to install the compressor rod into packing without damaging the seals. This tool is used only on W-7 frames.
Top
|
|
Main Bearing Removal Tool
914-691
Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on SW and MW compressor frames.
Top
|
|
|
Main Bearing Removal Tool
939-926
Sized to fit in the oil hole of the main bearing journal of the crankshaft. Care must be taken to roll the crankshaft in the correct direction; i.e. not against the bearing tang. This will damage the bearing. This tool can be used on W-7 and W-6 compressor frames.
Top
|
|
Handle for Crosshead
906-003
This tool is used to install and remove the crosshead from the crosshead guide. It comes in quantities of two that can be bolted together for storage.
Top
|
|
|
Handle for Crosshead
906-021
This tool is used to install and remove the crosshead from the crosshead guide. It comes in quantities of two that can be bolted together for storage.
Top
|
|
Adapter Tool
906-004
Top
|
|
Socket
906-005
Top
|
|
Wrench, Piston Rod
937-391
Top
|
|
Extension Tool
909-975
This tool is used to pull the valve chairs from the cylinders.
Top
|
|
T Handle
909-973
This handle is used to pull the valves from the cylinders.
Top
|
|
T Handle
909-971
This handle is used to pull the valves from the cylinders.
Top
|
|
Valve Disassembly Tool
909-977
Top
|
|
Valve Ring Clamp
919-541
Top
|
|
Valve Remover
917-041
This tool is used to pull the valve from the cylinder with the threaded female end.
Top
|
|
|
Valve Remover
917-042
This tool is used to pull the valve from the cylinder with the threaded female end.
Top
|
|
Puller, Compressor Piston
939-940
Top
|
|
Socket
939-938
Top
|
|
Socket, 3" Hex
S-8228
Socket with 3” internal hex used to loosen/tighten compressor rod piston nuts with 3” standard hex.
Top
|
|
Socket, 3" Flats
937-391
Socket with 3” internal flats used to loosen/tighten compressor rod piston nuts with 3” flats.
Top
|
|
Compressor Rod Nut Bar
S-8384
Used to break the compressor rod nuts loose. Bar is heat treated carbon steel. One end fits in 1” dia hole, other end fits in 1.06” dia hole.
Top
|
|
Wrench, Compressor Nut (12 pt)
S-8676
4” hex-12 pt wrench used to grip the compressor rod nut better.
Top
|
|
Wrench, Piston Rod 2 ½”
939-994
Used to loosen/tighten compressor rod from crosshead.
Top
|
